Dryer drum won’t turn: causes, safe checks and what is involved

Dryer drum repair is usually what follows when you press start, hear the motor, maybe feel a little heat, and the drum just sits there. Or it starts and stops. This is one of the most common dryer faults, and the cause is usually a mechanical part that wears out rather than anything electrical.
Table of Contents
Safe test: turn the drum by hand
Turn the dryer off and unplug it. Open the door and spin the drum by hand.
- It spins freely, with almost no resistance. The drive belt is probably broken or slipped off, since nothing connects the drum to the motor. This is the most likely result.
- It turns with a grinding, rough feel, or with a loud thump each rotation. A worn roller, glide or shaft bearing.
- It is stuck or very stiff. Something may be jammed, or the motor or drum bearing has seized. Look for a sock or underwire caught between the drum and the front panel.
Likely causes
Broken or worn drive belt
A single long belt loops around the drum and the motor pulley, through a spring-loaded idler pulley that keeps it tight. Belts stretch, glaze, and snap with age and use. When a belt breaks the motor still runs, so you hear it, but the drum does not move. Often there is a thumping sound before the belt fails.
Idler pulley
The idler pulley wheel wears or seizes, which causes squealing and then belt failure. Dryer drum repair that replaces only the belt, without checking the pulley and rollers, means the new belt may fail early.
Drum support rollers or glides
The drum rests on rollers, or on glides in some models. When they wear out, the drum sits lower, scrapes, and can rub against the cabinet. Rumbling, squealing and thumping are signs. Failure can also stop the drum turning.
Motor
If the motor hums and does not turn, even with a good belt, the motor, its centrifugal switch or start capacitor may be at fault on some models. Do not keep trying to start it, since a motor drawing too much current gets hot. A dryer motor also has an internal thermal protector that shuts it off when it overheats, then lets it restart after it cools. That points to a motor that is working too hard, which may come from a stiff drum, a blocked vent or a failing motor.
Door switch
If the dryer does nothing at all when you press start, the door switch may not be registering. That is a different problem from a drum that will not turn, but it is worth testing: with a good switch, you can usually hear the click as you shut the door.

What not to do
- Do not run the dryer with a stuck drum, a burning smell or a hot motor.
- Do not open the cabinet with the dryer plugged in. The terminal block, the heating element and the control carry full voltage.
- Do not bypass the door switch to make it run.
- For a gas dryer, dryer drum repair that needs the gas shut off, the dryer moved, or any work at the burner belongs to a professional. See dryer overheating and fire prevention for the safety rules around heat.
What dryer drum repair involves
On most dryers, the technician takes off the top or front panel, lifts or releases the drum, removes the old belt and checks the idler pulley, rollers, glides and the motor shaft and bearing seal for wear. A new belt is threaded around the drum and the motor pulley, over the idler, and the drum is put back and tested. Doing the belt alone is sometimes enough. When the rollers or pulley are worn, replacing them at the same visit avoids a repeat.
The cost of dryer drum repair depends mainly on whether the belt is the only worn part, or whether rollers, pulley and motor are involved, and on how easily your model comes apart. A technician can tell you after looking at it. The service call is $80, paid at your home or with PayPal or a credit card.

Lint and the drum
Lint that collects around the motor and belt is a fire risk and also makes belts and bearings run hot. Whenever a dryer is opened up for dryer drum repair, the cabinet should be vacuumed out. You can reduce the problem by cleaning the lint screen and vent as the dryer maintenance checklist describes. The National Fire Protection Association also publishes dryer safety tips.
Repair or replace
Dryer drum repair for a belt, rollers or an idler pulley is modest compared with a new dryer. A seized motor, a rusted-out drum or multiple failed parts on an old machine make a replacement worth considering. If you decide to replace, our guide to installing a new dryer covers what to check. We repair dryers and can tell you which route makes sense.
If you would rather have a technician look at it, book at /book/ or call (209) 843-0080 and ask for the next available window. The service call is $80, paid at your home or with PayPal or a credit card.

Common questions
Why does my dryer hum but the drum does not turn?
Usually the drive belt has broken or come off, so the motor runs without turning the drum. Spin the drum by hand with the power off. If it spins freely, the belt is the likely cause.
How can I tell if the dryer belt is broken?
With the dryer unplugged, rotate the drum by hand. A drum that turns with almost no resistance and no belt tension means the belt is broken or off. The belt itself is only visible with the panel removed.
Is it safe to keep running a dryer that squeals?
No. A squeal usually means a worn pulley, roller or bearing, and continued use can snap the belt or damage the drum.
Can a dryer with a seized motor be fixed?
Sometimes the motor can be replaced, but on an older dryer the cost compared with the age of the machine may favour replacing the dryer.