Washer installation checklist: hoses, leveling and the first run

This washer installation checklist covers what to look at before, during and after the install, because a badly installed washer shows up later as a flooded laundry room, a machine that walks across the floor, or a drain that backs up. Most of that is preventable with about an hour of care.
Table of Contents
Washer installation checklist: before the washer arrives
- Measure the space and the path. Check the doorway, hallway and any turns, not just the spot where it will sit. Leave room behind the machine for hoses and the drain, since sharp bends there cause leaks and kinks.
- Check the manual for clearances. It tells you how much gap is needed at the back and sides, and it belongs on your washer installation checklist.
- Look at the floor. It needs to be solid and reasonably flat. Soft or sagging flooring will make the washer vibrate, no matter how well you level it. Washers on upper floors move more, so a firm base matters even more there.
- Find the outlet. A standard grounded three-prong outlet within reach of the cord. Do not use an extension cord or a plug adapter that removes the ground.
- Check the taps. Hot and cold valves should open and close fully and not drip. If they are stiff, corroded or leaking, deal with them before you connect anything.
- Check the drain. A standpipe or a laundry sink drain, with the right height for the washer. The manual gives a range. Too low and the water can siphon out. Too high and the pump struggles.
Remove the shipping hardware
New washers are held steady for transport by bolts, a bracket, or foam blocks. Front-loaders almost always have bolts at the back. They must be taken out before the first use. If they stay in, the washer will shake violently and can damage itself. Keep the bolts and plugs in case you move later. It is an easy step to miss, so put it on your washer installation checklist.

Hoses
Hoses are the most common source of washer flooding, so this part of the washer installation checklist deserves time. For general laundry-room safety, the National Fire Protection Association publishes dryer and washing machine safety tips.
- Use new hoses. Do not reuse hoses from the old washer, and if you can, choose braided stainless steel hoses over the thin rubber ones. Braided hoses resist bulging, though they still age and should be checked.
- Hot and cold go to the right inlet. They are usually marked or colour-coded.
- Check the rubber washers. Each hose end needs a flat washer, and the washer inlet may have a small mesh screen that should be in place.
- Tighten by hand, then about a quarter to half a turn with pliers. Overtightening cracks plastic fittings.
- Leave a gentle curve, not a sharp bend, and do not let the hoses be pinched when the washer is pushed back.
- Open the taps slowly and look at every connection for drips, then dry them with a paper towel and check again after a few minutes. A slow drip shows up on dry paper.
Whatever hoses you use, look at them once or twice a year. Bulges, cracks, rust at the collar or a wet stain on the floor all mean replacing now. Some people turn off the taps when the washer is not in use for a long time, such as a holiday, as a cheap safeguard.
Drain hose
Hold the drain hose in its curved guide so that it cannot slip out of the standpipe. Do not seal the hose tightly into the standpipe, since air needs to escape. Keep the hose clear of kinks. If you use a laundry sink, tie the hose so that it cannot jump out under pump pressure, which would flood the floor.

Level the washer
Place a spirit level on top, side to side and front to back. Turn the adjustable feet until the bubble is centred, then lock the nuts. Push down on each corner. There should be no rocking. Do this after the hoses and drain are connected, and check it again after the first run. If you are fitting a washer on a pedestal, follow the manufacturer’s instructions for securing it.
First run
- Run a short cycle with no clothes, and stay nearby.
- Watch the hose connections at the taps and the back of the machine while it fills.
- Watch the drain during the pump-out for splashing or overflow.
- During spin, listen for loud knocks. A little noise is normal. Walking or banging is not.
- Check again for drips, and the floor around the machine, after the cycle finishes.

What a pro does differently
A professional follows the same washer installation checklist: checks the taps and the drain before disconnecting the old washer, fits new hoses, removes the shipping bolts, levels the machine and runs a test cycle while watching for leaks. If your washer is part of a stacked set or sits next to a gas dryer, installation is more involved, so ask before assuming it is a simple swap. You can read about what we install on our appliance installation page.
If a newly installed washer is shaking or will not drain after you have worked through the washer installation checklist, our washer troubleshooting guide is a good next read.
If you would rather have a technician look at it, book at /book/ or call (209) 843-0080 and ask for the next available window. The service call is $80, paid at your home or with PayPal or a credit card.
Still dealing with washer installation checklist? A technician comes to your home and finds the cause. See the pricing page for the service call, or book a visit for washer installation checklist.
Common questions
Do I need new hoses when I install a washer?
Yes, it is best to fit new ones. Old hoses have been under pressure for years and may be weak even if they look fine. Braided stainless steel hoses are a common upgrade.
What are the bolts on the back of a new washer?
They are shipping bolts that stop the drum moving in transit. They must be removed before the first use or the washer will shake badly and can be damaged.
How do I know if my washer is level?
Place a spirit level on top in both directions and adjust the feet until it reads level, then push on each corner to check it does not rock.
How high should the washer drain standpipe be?
It depends on the washer, so check the manual. Too low can siphon water out, and too high can strain the pump.